FPGA-based super waveform oscillator core featuring a centroid oscillator and six ‘sister’ oscillators using sampled waveforms that can be dynamically de-phased in the stereo field to produce wide and thick single-oscillator sounds in one of two ‘super modes’

Waveshapes: sine, sawtooth, square, triangle, noise and up to 32 Alternative Complex Waveforms that can be user updated

wave morphing between adjacent waves

FPGA-based oscillator core running at a very high sample rate with an algorithmic core

Waveshapes: SINE, SAWTOOTH, SQUARE, TRIANGLE, NOISE, PULSE WITH VARIABLE PULSE WIDTH

Can be hard-synced to DDS 1

LFO mode

Ring modulation mode

Square wave and Sine wave sub-oscillator modes

Controls the balance between the audio signals from DDS 1 and DDS 2 or DDS 1 and the sub oscillator

In shift mode, this parameter becomes a pan control, allowing you to position a layer within the stereo field

4-pole, 24 dB per octave, analog resonant low-pass filter that uses a classic polysynth filter design by Sound Semiconductor (SSI)

1-pole, 6 dB per octave, analog high-pass filter, preceding the low-pass filter

Two overdrive settings

Selectable keyboard tracking modes

Modulation by ENV 1 and/or ENV 2, LFO 1 and DDS 2

Analog VCA with selectable velocity sensitivity

Modulation by ENV 2 or one of two fixed envelopes, LFO 1 and DDS 2

ENV 1: 6-stage envelope (attack hold, attack, decay hold, decay, sustain, release) featuring inverted and loop modes with selectable key tracking

ENV 2: 5-stage envelope (attack, decay hold, decay, sustain, release)

MAIN LFO WITH LOW AND HIGH-FREQUENCY MODES

Can be used as a standard LFO, a third oscillator, as a drone, or for audio rate modulations

Waveforms: triangle, reverse sawtooth, sample & hold and square as well as any waveform DDS 1 is currently set to

Features controls for delay and left-right phase offset for binaural modulations

Free-running, reset and one-shot modes

Can be synced to the arpeggiator and sequencer or an external clock source

LFO 1 and ENV 1 pitch modulation (DDS 1 and/or DDS 2)

Selectable ‘super modes’ and detune spread control for DDS 1

Wave modulation allows for morphing between two DDS 1 waveforms, modulatable by LFO 1, ENV 1 or manually

PULSE-WIDTH CONTROL FOR DDS 2’S PULSE WAVEFORM, MODULATABLE BY LFO 1 OR ENV 1

Cross and ring modulation between DDS 1 and DDS 2

24-bit dual-mode stereo chorus per layer with three settings

Clock-syncable and modulatable 24-bit stereo delay per layer featuring a delay freeze function that enables you to create sound-on-sound loops while you are performing

Two-axis bender with LFO 2 trigger and dedicated controls for DDS1/2 pitch and VCF modulation

Variable portamento per layer

Playable spring-lever keyboard octave selector

LFO 2 with rate and delay controls, selectable trigger modes, six selectable waveforms (sine, reverse sawtooth, sample & hold, square, sawtooth, sample & glide) and dedicated controls for rate, pitch, VCF and VCA modulation

61-note, semi-weighted, velocity-sensitive keyboard with polyphonic aftertouch

Custom-designed ribbon controller for expressive modulation control, featuring an adaptive downbend behaviour that allows you to pitch bend notes down several octaves according to the pitch of the note you play

MPE support for external MPE controllers

Master volume, tempo and lower layer detune controls

Individual hold modes for each layer

Selectable keyboard modes for setting up a performance: Single, Dual and Split

Individual layer select buttons

Intuitive 8x8 modulation matrix with pre-defined sources and destinations

UP TO 24 MORE DESTINATIONS CAN BE MODULATED USING THE DIRECT PARAMETER MAPPING METHOD

LEDs give clear feedback on mappings and modulation amounts

Four selectable voice assign modes including two monophonic and two polyphonic modes

FIVE sELECTABLE UNISON MODES INCLUDING VARIOUS STACKED VOICE MODES

Binaural option allows for choosing between 10 true stereo ‘super voices’ or 20 non-binaural monaural voices in single layer mode

Front panel control to disable Binaural and enter fully true-mono audio output

MIDI-syncable multi-mode arpeggiator with smart hold option

MIDI-syncable 64-step sequencer with programmable step, slide, accent, rest and sequence length tracks

Clock parameters feature easy adjustable clock divider settings and swing per layer

128 PERFORMANCES (EACH CONTAINING 2 PATCHES), 256 PATCHES, 32 ALTERNATIVE WAVEFORMS FOR DDS 1 AND 16 SEQUENCES

Files can easily be copied to the internal memory or backed up using the USB port

Quick firmware updates via USB connection

AC power connector for worldwide use with a standard, grounded IEC power cord (90-250 volts, 50-60 Hz)

USB port FOR MIDI AND LIBRARY DUTIES

MIDI In, Out and Thru ports on 5-pin DIN sockets

Pedal inputs: volume, expression, sustain per layer and delay freeze per layer

Stereo mix output for summed layer signals (unbalanced 1/4 inch jacks)

Individual upper and lower layer stereo outputs for individual mixing and processing (unbalanced 1/4 inch jacks)

Easy to reach headphone output on the front side with both ¼ inh and 3.5mm stereo jack sockets

dimensions (mm): 1040l × 440w × 110h

weight: 14.5KG